Fluke FLK-VT04-ELEC-KIT Electrical Kit for Visual Infrared Thermometer, Includes IR Thermometer, Digital Multimeter, and True-RMS Clamp Meter

Price: $1,019.99 $550.21
Product prices and availability are accurate as of 2018-11-12 08:07:50 UTC and are subject to change. Any price and availability information displayed on http://www.amazon.com/ at the time of purchase will apply to the purchase of this product.
You Save: $469.78 (46%)
Availability: In Stock
Usually ships in 24 hours
CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON SERVICES LLC. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.

Manufacturer Description

The Fluke FLK-VT04-ELEC-KIT electrical kit includes a Fluke VT04 visual infrared thermometer, a Model 117 digital multimeter, and a Model 376 clamp meter. The VT04 visual infrared thermometer has a built-in digital camera, hi-low temperature alarms, time-lapse image capture and a measurement range of 14 to 482 degrees F (-10 to +250 degrees C). The thermal heat map has five levels of overlay that enable the operator to locate precisely the area of concern. The built-in digital camera takes time-lapse images and saves up to 10,000 images per gigabyte on a removable micro SD data card (4 GB card included). Images can be exported for long-term records retention or inclusion in reports using the included SmartView analysis and reporting software.

The Fluke Model 117 dual-impedance digital multimeter measures true RMS- AC amps and volts, DC amps and volts, continuity, ohms, capacitance, low impedance (LoZ) capacitance, and hertz. The meter has automatic AC/DC volt selection, true RMS AC measurements for accurate measurements on non-linear loads, and minimum, maximum, and average data for recording signal fluctuations. The meter also performs a diode test and measures resistance, continuity, frequency, and capacitance. Low impedance (LoZ) measurements deliver a low impedance input to the circuit, eliminating ghost voltages and improving accuracy. The white backlit LED is suitable for use in low lighting. Non-contact voltage detection speeds measurements. The meter includes test leads, holster, one 9V battery, and instructions.

The Fluke 376 true RMS AC/DC clamp meter measures 1,000 amp AC and DC current with the fixed jaw or 2,500 amp AC current with the flexible current probe. True RMS AC voltage and current measurements provide accurate readings on non-linear signals. The iFlex flexible current probe increases the measurement range to 2,500 amp AC and measures awkward-size conductors or in hard-to-reach areas. An integrated low-pass filter and signal processing provide stable readings in noisy electrical environments. Minimum, maximum, and average readings capture signal fluctuations. Inrush measurement technology filters out noise and captures the motor starting current as seen by the circuit protection. The meter has a CAT IV 600V, CAT III 1,000V safety rating. The meter includes an 18-inch iFlex probe, test leads, a soft carrying case, and instructions.

VT04 IR Thermometer Specifications
Detector typeUncooled pyroelectric ceramic
Thermal sensitivity (NETD)< or = 250mK
Field of view28 x 28 degrees
Image PalettesHot Metal, Ironbow, Rainbow, Rainbow High Contrast, Grayscale (white hot) and Grayscale (black hot)
Temperature range14 to 482 degrees F (-10 to +250 degrees C)
Image file format.is2 format saved to SD card; user can create professional reports or export images using supplied software (BMP, DIB, GIF, SPE, FIF, SPEG, JPG, PNG, TIF and TIFF)
Safety compliancesCFR47: 2009 Class A. Part 15 subpart B; CE: EN 61326:2006; IEC/EN 61010-1:2010 Pollution Degree 2, 2 m drop
Computer interfaceMicro USB connector
PowerRechargeable Li-ion battery, 3.6V, 2250 mAh, 8.1 Wh; 8 hour life
Dimensions (H x W x D)8.3 x 3 x 2.2 inches/21 x 7.5 x 5.5 cm
Weight10.5 oz./300 g

117 Multitester Specifications
Maximum voltage between any terminal and earth ground600V
DC millivolts range and resolution600.mV range with 0.1mV resolution
DC volts range and resolution6.000V range with 0.001V resolution; 60.00V range with 0.01V resolution; 600.00V range with 0.1V resolution
AC millivolts (true RMS) range and resolution600.0mV resolution with 0.1mV resolution
AC volts (true RMS) range and resolution6.000V range with 0.001V resolution; 60.00V range with 0.01V resolution; 600.0V range with 0.1V resolution
Continuity range and resolution600 ohms range with 1 ohm resolution
Ohms rangeup to 600.0 ohms
Diode test2.000V
Capacitance1000 nanofarads to 1000 microfarads
LoZ capacitance1 nanofarads to 500 microfarads
CertificationsUL, CSA, TUV, N10140 , VDE, IP42
Safety compliancesANSI/ISA 82.02.01 (61010-1) 2004; CAN/CSA C22.2 No 61010-1-04; UL 6101B (2003); EMC EN61326-1; and IEC/EN 61010-1 2nd Edition for measurement Category III, 600 V, Pollution Degree 2

376 Clamp Meter Specifications
AC/DC current measurement (fixed jaw)1,000 amp
AC/DC current measurement (iFlex current probe)2,500 amp AC
AC/DC voltage1,000V
Frequency (jaw and iFlex)Up to 500Hz
Resistance with continuity detection60 kilohms
DC millivolt500mV
Capacitance1,000 microfarads
Other testsContinuity
Data typesMinimum, maximum, and average
DisplayBacklit LCD
Wire capacity750 MCM or 2-500 MCM
Safety ratingCAT III 1000V, CAT IV 600V

*H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.

Digital thermometers are instruments used to measure the temperature of air, liquids, or surfaces electronically. They may measure temperature in Celsius, Fahrenheit, or both. Most digital thermometers use thermistors, which are small electronic resistors. Thermistors are made out of metals that conduct electricity within a certain range and become more conductive the warmer they get. A microcontroller inside the thermometer measures this electrical conductivity and converts it to a temperature, which is displayed on an LCD. Digital thermometers are used in a wide range of applications, including in laboratory settings, food service and storage, and in doctors' offices and hospitals.

Multimeters are electrical test meters that measure multiple properties of an electrical circuit, such as current, voltage, resistance, capacitance, and continuity. Available in handheld or benchtop models, multimeters diagnose electrical problems in electrical equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Multimeters display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltage. Safety ratings are based on International Electrotechnical Commission (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating.

Clamp meters, also called clamp-on meters, have two jaws that fit around a conductor to measure electrical current without cutting through wires, or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp meters diagnose problems in electrical equipment, wiring, and power supplies. All clamp meters test for current. Some come with test leads and inputs for measuring voltage, capacitance, and resistance. They display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltage. Safety ratings are based on International Electrotechnical Commission (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating.

Fluke Corporation manufactures electrical testing tools and software for industrial and commercial applications. The company, founded in 1948, is headquartered in Everett, WA.

What's in the Box?

  • Model VT04 visual IR thermometer
  • Model 117 electrician's digital multimeter
  • Model 376 AC/DC true RMS clamp meter
  • Micro-SD card and conversion adapter
  • 4 mm silicone test lead set
  • 18" iFlex flexible current probe for the 376 clamp meter
  • Li-Ion battery for VT04 visual IR thermometer
  • (2) alkaline batteries for the 376 clamp meter
  • Micro USB charger/power supply with worldwide adapters for VT04 visual IR thermometer
  • SmartView analysis and reporting software CD for VT04 visual IR thermometer
  • Lanyard
  • Hard case for VT04 visual IR thermometer
  • Holster for 117 digital multimeter
  • Soft case for 376 clamp meter
  • Multilanguage instruction CD
  • Instructions

Product Features

Electrical kit includes Fluke VT04 visual infrared thermometer, Model 117 digital multimeter, and Model 376 clamp meter to troubleshoot electrical, HVAC/R, and automotive applications VT04 visual infrared thermometer has a built-in digital camera, hi-low temperature alarms, time-lapse image capture and a measurement range of 14 to 482 degrees F (-10 to +250 degrees C) Model 117 dual-impedance digital multimeter measures true RMS AC amp and volts, DC amp and volts, continuity, ohms, capacitance, low impedance (LoZ) capacitance, and hertz Model 376 true RMS clamp meter measures AC current and voltage, DC current and voltage, resistance, frequency, capacitance, and continuity Meters meet industry standards for safety compliances